How to Replace a Kia Sportage Replacement Key
The key of a lot of Kia models comes with a keyless entry system built into. This key is similar to an remote control and can be exchanged with a Kia dealer.
Key fobs may stop working due to a variety of reasons, including the battery being dead, worn-out buttons signal interference or water damage. Here are some tips to help you get your Kia sportage replacement key to work again.
How do you replace the remote key or the smart key?
If your Kia is equipped with an intelligent key, remote key push-to-start key, or a regular non-transponder metal key, the battery in these keys will eventually require replacement. This is especially relevant if your vehicle displays a message indicating that the smart or remote keys aren't powered.
Fortunately, it's an easy procedure. To replace the battery of the keyfob, remove your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover off. A small screw is located inside the key fob that holds the battery in place. With a small screwdriver, remove the screw and pull out the battery that was in place. Install the new battery and close the cut on the key fob.
Test the key fob by pressing the lock/unlock buttons. You're in good shape when the doors lock or unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to run errands around Brandon.
Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a computer that is available only to the locksmith in the automotive or dealer. Other keys (non-transponder metal keys) don't require programming. If you want to change the programming of your key, it is necessary to note the key code's number on the key code tag.
How do you replace a dead battery?
If the Kia key fob is unable to respond to pressing the lock/unlock button, it is most likely that the battery is depleted. A weak battery can cause other issues such as the check engine light flashing on or delayed engine cranking. Fortunately, replacing the battery on the key fob is a relatively easy DIY project that requires only a few basic tools.
Before you begin the process be sure that your vehicle is turned off and all doors are closed. Locate the small plastic piece that is on the bottom of your key fob and jiggle it until a metal key slides out. kia ceed key fob replacement www.g28carkeys.co.uk can then insert the key in the handle on the door of your driver to unlock your car.
To replace the battery on the key fob remove the cover at the rear. Utilize a plastic plier tool to loosen the latch that holds the black negative cable. Remove the old battery, and then align the replacement battery so that its "+" side faces you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid damaging or breaking the contacts made of metal.
After you have installed the new battery, turn the key fob off and on in the ignition until the door locks cycle. You can then test the Kia's key fob once more to ensure it is working correctly.
How do I replace a smart key
You could have a standard keyfob, or a Smart Key, based on the model of Kia Sportage. The difference between these is that the smart key has a small mechanical key blade that is hidden inside, while the standard fob isn't equipped with. Both key fobs come with batteries that will eventually require changing. It's an easy task that will take about two minutes.
Be sure to switch off your Kia and sit on a level or well-lit surface prior to when you begin. Also, keep in mind that there are tiny components inside the fob that could be removed if not careful.
The first step is to locate the small release button on the back of the lower part of the fob. It will be either an oval silver button or a rectangular slot. You can open the key fob by pressing the button.
Once you have the key fob opened, you can simply take out the old battery and replace it. The new battery is a C2032, and can be purchased online or in your local auto parts shop. After you've finished with the battery, you should be able to lock or unlock your car with your key fob even if the engine isn't running!
How to replace a mechanical key
The Kia keyfob is an excellent convenience which allows us to lock or unlock our car with just pressing the button. Like any other device it may have issues from time to time. There are ways to fix these problems and keep your key fobs functioning for a long time.
One of the most common problems is a low or dead battery. This can cause the device to stop working altogether or work intermittently. If this happens try replacing the battery with a new one.
If this doesn't fix the issue then try using a normal flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not damage any internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a brand new one.
Close and open the door using the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob and verify that it's working correctly. Contact a dealer or a locksmith to fix the issue in the event that the fob is not working. Make sure they cut you an emergency key that functions across all trunk and door cylinders in order to avoid future lockouts.